New Mercedes-Benz MUS-MAX wood chipper
≈ US$866,500
Šentjur
If you decide to buy equipment at a low price, make sure that you communicate with the real seller. Find out as much information about the owner of the equipment as possible. One way of cheating is to represent yourself as a real company. In case of suspicion, inform us about this for additional control, through the feedback form.
Before you decide to make a purchase, carefully review several sales offers to understand the average cost of your chosen equipment. If the price of the offer you like is much lower than similar offers, think about it. A significant price difference may indicate hidden defects or an attempt by the seller to commit fraudulent acts.
Do not buy products which price is too different from the average price for similar equipment.
Do not give consent to dubious pledges and prepaid goods. In case of doubt, do not be afraid to clarify details, ask for additional photographs and documents for equipment, check the authenticity of documents, ask questions.
The most common type of fraud. Unfair sellers may request a certain amount of advance payment to “book” your right to purchase equipment. Thus, fraudsters can collect a large amount and disappear, no longer get in touch.
- Transfer of prepayment to the card
- Do not make an advance payment without paperwork confirming the process of transferring money, if during the communication the seller is in doubt.
- Transfer to the “Trustee” account
- Such a request should be alarming, most likely you are communicating with a fraudster.
- Transfer to a company account with a similar name
- Be careful, fraudsters may disguise themselves as well-known companies, making minor changes to the name. Do not transfer funds if the company name is in doubt.
- Substitution of own details in the invoice of a real company
- Before making a transfer, make sure that the specified details are correct, and whether they relate to the specified company.
Seller's contacts
Slovenia, Šentjernej
Slovenia, Šentjernej
Slovenia, Šentjernej
Slovenia, Šentjernej
Slovenia, Šentjernej
Slovenia, Šentjernej
Slovenia, Šentjernej
Slovenia, Šentjernej
Slovenia, Šentjernej
Slovenia, Šentjernej
Turkey, Konya
Germany, Gross-Umstadt
Germany, Kronach
Ukraine, Lviv
• Chipper drive via direct drive of the truck
• Input speed 1100 rpm
• Permissible drive power between 450 – 750 HP
• Advantage of fast and highly mobile transport (90 km/h) with the truck
1. STANDARD EQUIPMENT
• Inlet opening width 137 cm
• Inlet opening height 80 cm
• Upper and lower hydraulic feed rollers
• Feed chain with rollers, length 2.50 m (standard), driven via a special hydraulic motor
• Emergency on/off switch on both sides
• Hydraulic closing/opening of the operating table
• Feed table width 2.55 m
• Upper feed roller with quick-change blades/teeth
• Machine rotor equipped with offset knives
• 1 x Standard screen or separation mesh with openings (size by agreement)
• Chipping discharge pipe with a diameter of 300 mm, discharge pipe hydraulically adjustable in height/length, rotatable, with approx. 80 cm hydraulic extension option for the radius of the upper part of the discharge pipe (length 3.5 m to 4.3 m), 3-part upper cover of the discharge pipe electrically adjustable, 1x spotlight mounted on the discharge pipe
2. HYDRAULIC COMPONENTS
• Hydraulic electromagnetic valves 24V
• 3-stage hydraulic pump
• LS adjustable hydraulic pump for the feed chain
• Gear pumps for the feed augers, chipper and hydraulic functions of the discharge pipe
• Hydraulic oil cooler with thermostat (500C)
• Hand pump
• 3 x mounted pressure gauges for monitoring system pressure
• Hydraulic oil tank 300 l
3. HYDRAULIC DRIVE OF THE DISCHARGE SYSTEM
• Discharge fan with a diameter of 1150 mm, including installation of an additional distribution gearbox
• Hydraulic drive of the discharge blades
• Additional hydraulic reservoir
• Additional hydraulic oil cooler
• Discharge system continuously adjustable within its operating range
4. CONTROL
• Process unit for the chipper (electrical cable control) 8 m cable with attached plug
• Graphical screen with guided menu for optical display and control of the following functions
5. POS 1
Automatic control of the inlet opening depending on the rotor speed of the chipper (stop/reverse/forward – automatic). Adjustable in % and fixed speed, PVG valve
POS 2: Electro-hydraulic control system for the following functions:
• Control of the chain on the chipper table (forward/end/reverse)
• Control of the chain on the chipper table (raise/lower)
• Steplessly adjustable speed (displayed on the screen in %)
• Feed rollers (raise/lower, pressure 80 bar)
• Discharge pipe adjustable (up/down/left/right/rotation)
• Upper part of the discharge pipe adjustable (up/down)
• Discharge pipe adjustable (longer/shorter)
POS 3
Input for foot pedal and input for remote controls available
POS 4
Operating hours counter for the chipper itself, rotor, feed chain, hourly counter for 10 customers
POS 5
Electronic monitoring of control and functions on the chipper, including automatic diagnosis of possible faults on the display screen and notification in case of a fault. Also monitors maintenance cycles for easier maintenance of the chipper.
6. BELT PULLEY
• Chipper drive via 10-groove pulley with appropriate protection
• Pneumatic belt tensioning (air from the truck)
ADDITIONAL EQUIPMENT:
• ALU tool box on the chipper
• Electro-hydraulic opening of the rotor cover
• Working platform for knife replacement, “SAFETY” system
7. ROTOR 6R12
Design with 6 knives, 120 degrees offset
8. Upper roller system
Upper roller system with the option of replacing the feed “teeth” on the roller. When they become worn, they are not welded but simply replaced.
Art.No.: V020-90-900246
Sliding holder for screens/meshes at the rear of the discharge system, for easier replacement of screens/meshes
Art.No.:
Electro-hydraulic opening of the rotor cover via
Art.No.: V020-90-900102
FOOT PEDALS:
By choice or according to preference, any two functions can be selected
Standard: (inlet roller pressure 80 bar, raise inlet roller)
Supplied with 1.5 m long cable and attached switch
Art.No.: V020-90-900303
BEKA MAX central lubrication for 15 most important lubrication points with grease quantity monitoring via the main display
Art.No.: V020-90-900932
Reversing camera including 7-inch color display, complete with cable connection
Art.No.: V020-90-900933
Additional camera mounted on the discharge system, connected via the reversing camera system
Art.No.: V20-900937
MUS-MAX SFC “Smart Feed Control”
Automatic feed control – synchronously controls feed speed / rotor operating speed / upper roller angle
This ensures even and gentle operation of the chipper as well as optimal chip quality
Art.No.: K640-023500
20 m hose on a reel for blowing out wood chips – Rollfix
Art.No.: V020-90-900705
Tool box with special tools –
39-piece tool set required for the chipper
Art.No.: V020-900715
MAINTENANCE PACKAGE:
• 2 x high-pressure filters
• 1 x attachment for adjusting the knives
• 1 x attachment for sharpening the knives
• ……
Art.No.: V020-900575
Screen 80/100 mm WT 11 XL – due to its size, supplied in two parts
Art.No.: V020-90-900025
12 pieces of knives for the chipper on 3 x grooves (245/233/20 mm), weight per piece approx. 6.84 kg
Art.No.: V020-90-900304
Lubrication for the hydraulic crane (connected to the MUS-MAX system)
Art.No.: V020-90-900254
Hydraulic oil tank with a capacity of approx. 330 l for the hydraulic crane pump
Art.No.: V020-90-900700
Hydraulic oil cooler with thermostat (50°C) for EPSILON crane
NON-FOLDING CRANE PALFINGER-EPSILON M100LD97
Design Non-folding crane within the width of the vehicle, manufactured according to the latest standards EN12999: 2011 HC1/ HD4/B4
• Lifting moment 85.0 kNm
• Maximum hydraulic reach 9.7 m
• Lifting capacity at 9 m 870 kg (gross)
• Lifting capacity at 3 m 2,830 kg (gross)
• Column slewing system Double slewing system with toothed rack in an oil bath, guided piston and end stop, slewing angle 425°
• Slewing moment 24.0 kNm
• Hose protection valve with restrictors on the cylinder of the lifting, articulated and telescopic arms
• Dead point Via stabilizers (or by agreement)
• Control from the crane operator's cab
• Support (RX39) Integrated stabilizers, hydraulic extension horizontally to 3.90 m hydraulically rotatable through 450°
• Rotator (G 121) Indexator 12 t + suspension BK047 (factory-mounted) EPSLINK
• Hoses 4-fold hose routing, routed inside the telescopic arm
• Design CE: with restrictor on the cylinder of the lifting, articulated and telescopic arms, pressure gauge
• Emergency stop switch
• Accessories Protection for articulated cylinders, pins, 2x mounted spotlights
• Color RAL 3020
• Weight without attachments 2,180 kg
• System pressure 200 bar
• Mounting kit for crane
2A. ADDITIONAL EQUIPMENT FOR CRANE:
DM9L
Single-circuit hydraulic installation, Danfoss PVG 32 control block
• 9 functions (6 proportional + 3 functions 0/1 for stabilizer legs)
• Block prepared for LS pump
• Pressure filter 180 l/min
• Emergency stop – electro-hydraulic valve after pressure filter
• Electrical connection with AMP connectors to the distribution block
• Block with electrical cabinet mounted laterally on the side cylinders
• Protection for complete block
PROFI1
Danfoss Professional joystick controls including controls
• 3x proportional functions
• 4 x on/off buttons and 10 m cable
FG 31 R
Biomass grapple, gripping area 0.36 m² maximum jaw opening width 1,580 mm, lifting capacity 4,000 kg, weight 200 kg, max. operating pressure 250 bar
Design with conical bushings for pins without play
SD
Hydraulic pressure spike suppressor for rotation and main arm
RAL
Color RAL BLACK 9005
AZV
Reinforced stabilizer piston rods
BK092
Suspension with slewing brake on crane (MPB100)
TVS
Extended stabilizers by 170 mm – fixed plates
BL463
Hoses from rotator to grapple (2 pieces)
RX47
Wide stabilizers (3.9 m)
GUM
Rubber bumper on auxiliary arm
CHIPPER DRIVE VIA TRUCK
Art.No.: V020-90-900900
NMV HACKER TRUCK PACKAGE
LARGE DISTRIBUTION GEARBOX
• special lubrication system
• additional 24V oil cooler
• additional filter
• oil tank
• special flange
• modification of the auxiliary frame
2x special cardan shafts for driving the chipper, from the NMW vehicle drive to the transmission drive assembly and from the transmission drive assembly to the chipper drive
TRUCK MERCEDES AROCS
Art.No.: V020-50-990058
• MB AROCS 3263 8X4
• EURO 6
• Power 630 hp
• “L” vehicle cab
• Wheelbase 3900 mm
• Fuel tank capacity 570 l + 60 l AdBlue
• Standard front axle 9,000 kg
• Rear axles 2 x 13,400 kg
• Tag axle 8 t
• Standard PSP module for connecting the vehicle to the chipper
• NMV transmission drive 1.2
• Suitable PTO for driving the LS hydraulic pump of the crane
• Comfort sprung driver's seat, seat heating
• Air conditioning + additional air conditioning for the vehicle's working cab (OPTION)
• Front air intake
• MBUX Multimedia Cockpit